MAUDE data represents reports of adverse events involving medical devices. This maude entry was filed from a 06,07 report with the FDA on 2015-05-04 for UMBILICAL CORD CLAMP 6833 manufactured by Deroyal Industries.
[5824031]
The clamps slid off the babies.
Patient Sequence No: 1, Text Type: D, B5
[13450271]
Investigation findings: initial investigation: deroyal is the manufacturer of finished good 6833, umbilical cord clamp, which has a report of "when the clamp was placed on the baby the clamp slid off. " the bom was reviewed, on (b)(6) 2012, and raw material (b)(4) was identified. The raw material is a vendor supplied product. Confirmation on vendor needed prior to a scar being issued. Due to multiple vendors listed in the jde operating system the qc complaint specialist requested assistance from the qc to identify the vendor. The qc reviewed the past products received in bp 34. Determined the vendor was (b)(4). A car was issued on 6/14/2012. The vendor issued the completed car on 8/6/2012. In addition, the qc complaint specialist reviewed the 2010, 2011, and 2012 sales information and call history logs. Deroyal has sold (b)(4) each of raw material (b)(4), umbilical cord clamps. The call history log review found similar reports. Updated: a further review of the complaint has identified that the complaint will be required for updates. Deroyal regulatory department has been notified of the re-opening of the report. The sample was returned to deroyal and provided to (b)(4) for evaluation. This information is documented within the sample retrieval process of the initial complaint investigation worksheet. Due to receiving (b)(4) during the investigation process of (b)(4) and had the same failure mode; therefore, (b)(4) was notified of the new event. The additional report, (b)(4), contained a lot number (the lot number was not identified for call (b)(4)); lot information was added to the deroyal plastics group problem analysis report and car response that was completed for call (b)(4). Within the car response it is detailed that a design change was implemented in 6/2012 and approved through eco (b)(4). Deroyal also evaluated the clamp compression force of the device through validation protocol acd. Pcl. 049- comparative testing of cord clamp compression force. Refer to the validation protocol acd. Pcl. 049 attachment. In addition, the 2013; 2014; and 2015 qfi logs were reviewed utilizing the keyword "umbilical" to identify if customer complaints have been received for the raw material (b)(4) or finished goods that contain the raw material. There have been no complaints received during the review period. Deroyal utilizes raw material (b)(4) within multiple product lines and multiple branch plants. Refer to the products using (b)(4) sales in selling attachment for a listing and sales information of components that contain the finished good. Correction: a correction has not been taken. Root cause analysis: evaluation results/root cause deroyal plastics group: the lot history record for the referenced lots was reviewed and it was confirmed that the lots met all specifications prior to release. As due diligence, and inventory verification was performed and it was identified that no product remained on hand for these lots. A recent study conducted by engineering, where cord clamps were submitted to a series of test reveals that "during testing, no failures were observed of either the latching mechanism or hinge. " updated: the true root cause for the reported issue is unable to be identified. Potential root causes have been identified but are not limited to the following: product defect during the manufacturing process; end user failing to follow the ifu and not ensuring the product was applied correctly and fully closed; and end user error failing to follow the ifu and cutting the umbilical cord too close to the cord clamp resulting in slippage of the clamp. Corrective action and/or systemic correction action taken: initial investigation: refer to the attached car response. Updated: as a result of an engineering study, an opportunity was identified. The main improvement was having more curve to the tooth profile. It was decreased from a radius of 19. 1 inches to a radius of 11 inches. This adds to the closing force and keeps more pressure in the center of the clamp. The secondary change was adding about. 015 inches of added height to the back rid. This should make the clamp have a slightly higher closing force. The first lot number manufactured after the changes have been identified as lot 12061431. Updated: due to the investigation and root cause determination a preventive action has not been taken. This report is being filed due to a retrospective review of complaints. This complaint has been re-opened for further investigation. A supplemental report will be filed if further investigation provides information which changes the content of this report.
Patient Sequence No: 1, Text Type: N, H10
| Report Number | 1033554-2015-00005 |
| MDR Report Key | 4749172 |
| Report Source | 06,07 |
| Date Received | 2015-05-04 |
| Date of Report | 2015-04-30 |
| Date of Event | 2012-06-18 |
| Date Facility Aware | 2012-06-18 |
| Report Date | 2015-04-30 |
| Date Mfgr Received | 2012-06-18 |
| Device Manufacturer Date | 2011-07-01 |
| Date Added to Maude | 2015-06-17 |
| Event Key | 0 |
| Report Source Code | Manufacturer report |
| Manufacturer Link | Y |
| Number of Patients in Event | 0 |
| Adverse Event Flag | 3 |
| Product Problem Flag | 3 |
| Reprocessed and Reused Flag | 3 |
| Health Professional | 3 |
| Initial Report to FDA | 3 |
| Report to FDA | 3 |
| Event Location | 3 |
| Manufacturer Street | 200 DEBUSK LANE |
| Manufacturer City | POWELL TN 37849 |
| Manufacturer Country | US |
| Manufacturer Postal | 37849 |
| Manufacturer Phone | 8653622333 |
| Single Use | 3 |
| Previous Use Code | 3 |
| Event Type | 3 |
| Type of Report | 3 |
| Brand Name | UMBILICAL CORD CLAMP |
| Generic Name | DEVICE, OCCLUSION, UMBILICAL |
| Product Code | FOD |
| Date Received | 2015-05-04 |
| Catalog Number | 6833 |
| Lot Number | 26448516 |
| Device Expiration Date | 2016-06-15 |
| Operator | HEALTH PROFESSIONAL |
| Device Availability | Y |
| Device Age | DA |
| Device Eval'ed by Mfgr | Y |
| Device Sequence No | 1 |
| Device Event Key | 0 |
| Manufacturer | DEROYAL INDUSTRIES |
| Manufacturer Address | 700 MARTIN LUTHER KING, JR. BLVD SANFORD FL 32771 US 32771 |
| Patient Number | Treatment | Outcome | Date |
|---|---|---|---|
| 1 | 0 | 1. Required No Informationntervention | 2015-05-04 |