Veterinary Sodium Chloride Injection, USP

For Animal Use Only

Sodium Chloride Injection, USP is a sterile, nonpyrogenic solution for fluid and electrolyte replenishment in single dose containers for intravenous administration. It contains no antimicrobial agents or preservatives. Discard unused portion. Composition, osmolarity, and ionic concentration are shown in Table 1:

Table

Sodium Chloride Injection, USP has value as a source of water and electrolytes. It is capable of inducing diuresis, depending on the clinical condition of the patient.

Sodium Chloride Injection, USP is indicated as a source of water and electrolytes.

None known. 

Sodium Chloride Injection, USP should be used with great care, if at all, in patients with congestive heart failure, severe renal insufficiency, and in clinical states in which there exists edema with sodium retention.

The intravenous administration of Sodium Chloride Injection, USP can cause fluid and/or solute overloading resulting in dilution of serum electrolyte concentrations, overhydration, congested states, or pulmonary edema. The risk of dilutive states is inversely proportional to the electrolyte concentration of the injections. The risk of solute overload causing congested states with peripheral and pulmonary edema is directly proportional to the electrolyte concentrations of the injections.

In patients with diminished renal function, administration of Sodium Chloride Injection, USP may result in sodium retention.

Reactions which may occur because of the solution or the technique of administration include febrile response, infection at the site of injection, venous thrombosis or phlebitis extending from the site of injection, extravasation, and hypervolemia.

If an adverse reaction does occur, discontinue the infusion, evaluate the patient, institute appropriate therapeutic countermeasures and save the remainder of the fluid for examination if deemed necessary.

Clinical evaluation and periodic laboratory determinations are necessary to monitor changes in fluid balance, electrolyte concentrations, and acid base balance during prolonged parenteral therapy or whenever the condition of the patient warrants such evaluation.

Caution must be exercised in the administration of Sodium Chloride Injection, USP to patients receiving corticosteroids or corticotropin. 

Do not administer unless solution is clear and seal is intact.

As directed by a veterinarian. Dosage is dependent upon the age, weight and clinical condition of the patient, as well as laboratory determinations.

Parenteral drug products should be inspected visually for particulate matter and discoloration prior to administration whenever solution and container permit.

All injections in plastic containers are intended for intravenous administration using sterile equipment.

Additives may be incompatible. Complete information is not available. Those additives known to be incompatible should not be used. Consult with pharmacist, if available. If, in the informed judgment of the veterinarian, it is deemed advisable to introduce additives, use aseptic technique. Mix thoroughly when additives have been introduced. Do not store solutions containing additives.

In an event of overhydration or solute overload, re-evaluate the patient and institute appropriate corrective measures. See Warnings. Precautions and Adverse Events.

Veterinary 0.9% Sodium Chloride Injection, USP in plastic container is available as follows:

How Supplied

Plastic Container:

PVC Free, DEHP Free, Latex Free

To Open
Tear overwrap down side at slit and remove solution container.  Some opacity of the plastic due to moisture absorption during the sterilization process may be observed.  This is normal and does not affect the solution quality or safety. The opacity will diminish gradually.  Check for minute leaks by squeezing inner bag firmly.  If leaks are found, discard solution as sterility may be impaired.  If supplemental medication is desired, follow directions below.

Preparation for Administration
1.  Suspend container from eyelet support.

2.  Remove protector from outlet port at bottom of container.

3.  Attach administration set.  Refer to complete directions accompanying set.

To Add Medication
WARNING:  Additives may be incompatible.

To add medication before solution administration
1.  Prepare medication site.

2.  Using syringe with 19 to 22 gauge needle, puncture resealable medication port and inject.

3.  Mix solution and medication thoroughly. For high density medication such as potassium chloride, squeeze ports while ports are upright and mix thoroughly.

To add medication during solution administration
1.  Close clamp on the set.

2.  Prepare medication site.

3.  Using syringe with 19 to 22 gauge needle, puncture resealable medication port and inject.

4.  Remove container from IV pole and/or turn to an upright position.

5.  Evacuate both ports by squeezing them while container is in the upright position.

6.  Mix solution and medication thoroughly.

7.  Return container to in-use position and continue administration.

CAUTION:  Federal law restricts this drug to use by or on the order of a licensed veterinarian.

Manufactured for

BrandDirections for use of plastic container

Vedco, Inc.
5503 Corporate Dr.

St. Joseph, MO 64507  USA

Printed in El Salvador

For a copy of the Safety Data Sheet (SDS) or to report adverse reactions call Vedco, Inc. customer service at 1(888) 708-3326

© 2015 Vedco, Inc.

NDC 50989-895-16

Veterinary 0.9% Sodium Chloride Injection, USP
500 ml

NDC 50989-895-17

Veterinary 0.9% Sodium Chloride Injection, USP
1000 ml

Label 2